Trucking for metals and steel
Lifetime Logistics Services LLC moves metals and steel across the western states, whether the load leaves a mill, a service center or a fabrication shop: open deck pieces travel on flatbeds and step decks supplied by vetted carriers, and boxed or crated metal goods can ride in 53 foot dry vans. Our Covina, California dispatch desk works through the weight, the securement and the unloading plan with you before any truck is booked. Phone (562) 566-8953 or complete the quote form here, listing the pieces, the weight and both addresses.
What metal freight rides on
Most steel leaves the plant on an open deck. Beams, angle, channel, plate, rebar bundles and long lengths of pipe or tube are set on the deck by a side forklift or an overhead crane, which a van door cannot accept, so they travel on a 48 or 53 foot flatbed. Pieces too tall for a standard deck move to a step deck, whose dropped main deck gives a tall piece extra clearance below the height limit.
Not every metal product needs an open trailer. Fasteners, fittings, wire on spools, sheet in crates and aluminum extrusions in boxed bundles usually come off a dock on pallets, and those go in an enclosed van where they stay dry and out of sight. When the order is a few bundles rather than a full deck, a hot shot or a partial share of a trailer may price lower than booking a whole truck.
Coils, weight and securement
Coiled steel concentrates a great deal of weight on a very small patch of deck. One coil can weigh tens of thousands of pounds, so where it sits decides whether each axle group stays legal. Federal cargo securement rules include a section written only for metal coils, and a coil load needs the chains, binders, coil racks or cradles and dunnage that section calls for. Tell us it is coil on the quote request, and we book a vetted carrier set up for it.
Weight is the other ceiling. The federal gross limit is 80,000 pounds for tractor, trailer and cargo together, with 34,000 pounds allowed on a tandem axle group, and a standard flatbed leaves room for roughly 48,000 pounds of freight. Steel hits that figure long before it covers the deck, which is why every piece needs a scale weight from you rather than a guess, and the load is planned around it.
Tarps, edges and finished surfaces
Hot rolled beams and rebar commonly travel bare, since a little surface rust does them no harm. Cold rolled sheet, galvanized coil, stainless, aluminum and painted or primed fabrications are another matter: rain and road grime mark them, so they go under steel tarps, and corner protectors keep chains and straps from biting into edges and coatings. Say which kind of freight you have when you ask for a price, because tarping adds time at the pickup.
At the delivery end, check that the receiver has a crane or a forklift rated for the heaviest piece. Small shops and construction sites sometimes do not, and no driver can unload a bundle of plate by hand. If nothing on site can lift it, tell us early, so the unloading is settled before a truck is sent.
Lanes that carry metal
Phoenix fabricates and stocks structural steel, rebar and racking for solar projects, and open deck trucks take it west on Phoenix to San Diego and northwest on Phoenix to Salinas, where growers put it into packing sheds and coolers. From the Central Coast, Salinas to Reno carries steel and building parts east to Reno and Sparks.
Mining country draws pipe and steel as well. Las Vegas to Reno runs up US 95 past the central Nevada gold mines, while the haul east to Salt Lake City crosses the Elko and Winnemucca mining district on Interstate 80. Fabricated steel and glass for hotel and resort jobs rides with Bay Area loads bound for Las Vegas, and yards around El Paso ship steel and pipe toward Tucson and southern Arizona.
Who hauls it and how it is priced
The tractors we own are matched to 53 foot dry vans, so boxed and crated metal goods may go out with our own drivers. Open deck trucks of every size are owned by outside carriers that haul for you under our federal broker authority, MC 1302550 and USDOT 3711199, and Highway, a carrier vetting service, checks each one's operating authority, insurance coverage and identity ahead of any load we hand it. Whichever truck it is, the same Covina dispatcher follows your metal from the plant gate to the receiver's signature.
Each metals load is priced on its own. To quote it we need:
- Product and form: coil, plate, sheet, beam, rebar, pipe, tube or boxed goods
- Heaviest single piece: its weight and size, plus the load total
- Loading and unloading method at each end: overhead crane, side forklift or dock
- Tarp needs, and any finish that must arrive unmarked
- Pickup and delivery addresses, dates and receiving hours
Questions shippers ask
- Can steel coils go in a dry van?
- Some can, when the coil is small enough to block and brace inside and the van floor can carry that much weight on one spot. Most coils travel on a flatbed in a coil rack or cradle, where the driver can chain them to the deck. Send the coil weight, width and diameter and we will say which trailer fits.
- Do you haul oversize steel?
- A load wider than the legal limit, taller than an ordinary flatbed can carry, or heavier than its rating needs state permits and sometimes escort vehicles. That is not routine work for us. Send us the dimensions and you get a straight answer on whether one of our vetted carriers can take it.
- How much steel fits on one flatbed?
- By weight, roughly 48,000 pounds on a standard flatbed, and less if the tractor or trailer is heavy. The deck has far more space than steel can legally fill, so weight decides almost every load.
- Can you move imported metal goods from the ports?
- Yes. Fittings, fasteners and other metal products that land in containers at the San Pedro Bay terminals can be pulled by a drayage carrier with port access, then sent on in a van or on a flatbed once they are unloaded.
Ready to price a load?
Send the quote form or call us. Quotes within 15 minutes, Monday to Friday 6 AM to 6 PM Pacific; operations team available 24/7 for active loads.